点击图片查看原图
FMC-GE8213-MIN
10/100/1000BASE-TX to 1000base-X(SFP) Mini Gigabit Fiber Media Converter PCBA, Without SFP module
Overview
The FMC-GE8213-MIN Media Converter complies with IEEE802.3z, IEEE802.3ab Standards It is designed to convert data signal between 10/100/1000 base-T and 1000base-X(SFP) Gigabit Ethernet.
It supports 10/100/1000base-T and 1000base-X applications. The data signal converted by such high performance media converter can be transmitted up to 100km (depend on SFP module) maximum by single-mode 9/125um fiber-optical cable from RJ45 Cooper Cat.5 or Cat.6 network cable.
The Converter is one SFP, one RJ-45 Jacks and one power supply receptacle. LEDs indicators are built-in for easy diagnosing and monitoring the status, it is mini designed for easy install and application. 5~12VDC wide range input.
Specifications:
Mechanical Parameters
|
External Power adapter |
68mm*36mm*22mm（L*W*H） |
|
Weight (internal PWR) |
0.1kg |
|
Performance introduction (Table 1)Parameter |
Type |
|
Data rate (Mbps) |
10/100 /1000 |
|
Optical wavelength (nm) |
850,1310,1550,CWDM for option Depend on SFP |
|
Fiber type(μm) |
Multi mode 62.5/125 or 50/125um Single mode 9/125um Depend on SFP |
|
Connector type |
LC(SFP) |
|
Max distance (km) |
0.5~100km , Depend on SFP |
|
Power supply |
5~12VDC |
|
Operating temperature |
-20～75℃ |
|
Storage temperature |
-40～80℃ |
|
Relative humidity |
5% to 90% non condensing |
Table 1: performance introduction
Features:
1). Support the IEEE802.3 fast Ethernet standard (10Mbps)
2). Support the IEEE802.3u Fast Ethernet standard(100Mbps)
3). Support the IEEE802.3ab and IEEE802.3z Gigabit Ethernet standard (1000Mbps)
4). Full-duplexes, half-duplex auto negotiation
5). 10M/100M/1000M bit rate auto negotiation
6）5~12VDC input by external power adapter
7). Automatic identification of MDI/MDI-X cross line.
8). Max.9000 bytes packet at cut-through mode, Max.2046bytes packet at store-and-forward mode.
9).low power consumption low heat.
10) Very lower BER rate, <1/1000000000
11) Time Delay:
Store-and-forward mode:9.6us,
Cut-through mode: 0.9us
12). In conformity to safety code of FCC, CE certification.
Interface
RJ-45 interface
The transmission media adopts Cat5 or Cat6 twisted-pair with typical length of 100 meter. It features the function of automatically identifying the through line and cross wire
Fiber interface
LC fiber interface is of duplex mode type, including two interfaces, namely TX and RX. When the two sets of optical transceiver are interfaced or connected to switch with fiber interface, the fiber is in cross connection, namely "TX-RX", "RX-TX" (direct butting for single optical fiber).
Connection
The network device (work station, hub or switch) with RJ-45 interface is connected to RJ-45 jack, and the fiber is connected to SFP optical transceiver. The corresponding LED is on for correct connection. (See the table below for the LED indicator lamp)
Specifications
|
Technical Parameter: |
|
|
Standards: |
IEEE 802.3 、IEEE 802.3z、IEEE 802.3u、IEEE 802.3x、IEEE 802.3i、IEEE 802.3ab |
|
Fiber Cable: |
1000base-SX: 50/125，62.5/125µm multi-mode 1000base- LX/ZX: 9/125µm single-mode. |
|
UTP Cable: |
Cat.5e or Cat.6 cable up to 100m. |
|
Data Transfer Rate:
|
RJ45 port: 100M, 1000Mbps auto-sensing SFP: 1000Mbps |
|
Duplex Modes: |
RJ45 port: Full/Half , auto- negotiation SFP: full-duplex mode |
|
Power supply: |
Input: 5~12VDC wide range |
|
Operating Temperature: |
-20 ~ 75 ℃ |
|
Humidity: |
5%~90% |
|
Storage Temperature: |
-40~ 80 ℃ |
|
Dimension: |
68mm*36mm*22mm（L*W*H） |
